| Network number of phases |
Single phase
Three phase |
| [Us] rated supply voltage |
200…240 V (- 10…15 %) for three phase
200…240 V (- 20…15 %) for single phase |
| Supply voltage limits |
200…255 V three phase
170…255 V single phase |
| Supply frequency |
50/60 Hz – 5…5 % |
| Network frequency |
47.5…63 Hz |
| EMC filter |
Without EMC filter |
| Continuous output current |
4.5 A at 16 kHz |
| Output current 3s peak |
13.5 A at 220 V |
| Continuous power |
750 W at 220 V |
| Nominal power |
0.75 kW at 220 V 16 kHz |
| switching frequency |
16 kHz |
| Overvoltage category |
III |
| Maximum leakage current |
1.3 mA |
| Output voltage |
<= power supply voltage |
| electrical isolation |
Between power and control |
| Type of cable |
Shielded motor cable (temperature: 0…55 °C) copper |
| Electrical connection |
Spring terminal, clamping capacity: 0.82…1 mm², AWG 18 (L1-L2)
Spring terminal, clamping capacity: 0.82…1 mm², AWG 18 (R, S, T)
Spring terminal, clamping capacity: 0.82…1 mm², AWG 18 (U, V, W, PE)
Spring terminal, clamping capacity: 0.82…1 mm², AWG 18 (PA/+, PBe) |
| Discrete input number |
8 programmable (CN1)
1 pulse train input (PTI) (CN1)
2 fast capture (CN1)
1 safety function STO (CN9) |
| Discrete input voltage |
24 V DC for logic |
| Discrete input logic |
Positive or negative (CN1) |
| Discrete output number |
5 logic output (CN1) at 12…24 V DC
1 pulse train output (PTO) (CN1) |
| Discrete output voltage |
12…24 V DC |
| Discrete output logic |
Positive or negative (CN1) |
| analogue input number |
2 |
| Absolute accuracy error |
0.1 % |
| Analogue input type |
V_REF voltage analog input: – 10…10 V, impedance: 10 kOhm, resolution: 14 bits
T_REF voltage analog input |
| Control signal type |
Servo motor encoder feedback CN2 |
| Protection type |
Against reverse polarity: inputs signal
Against short-circuits: outputs signal
Overcurrent: motor
Overvoltage: motor
Undervoltage: motor
Overheating: motor
Overload: motor
Overspeed: motor |
| Safety function |
STO (safe torque off), integrated |
| Safety level |
SIL 2 conforming to IEC 61800-5-2: 2007
SIL 2 conforming to IEC 61508-1: 2010
PL d/category 3 conforming to ISO 13849-1: 2008
SIL 2 conforming to ISO 13849-1: 2009/AC
SIL 2 conforming to IEC 60204-1: 2006
SIL 2 conforming to IEC 60204-1: 2009/A1
SIL 2 conforming to IEC 60204-1: 2010/AC
SIL 2 conforming to IEC 62061: 2012 |
| Communication interface |
CANopen, integrated
CANmotion, integrated |
| Connector type |
RJ45 (CN4) for CANopen, CANmotion |
| Method of access |
Slave |
| Transmission rate |
250 kbit/s for bus length of 100…250 m for CANopen, CANmotion
500 kbit/s for bus length of 4…100 m for CANopen, CANmotion
1 Mbit/s for bus length of 4 m for CANopen, CANmotion |
| Number of addresses |
1…127 for CANopen, CANmotion |
| Physical interface |
RS485 for Modbus Serial line slave |
| Status LED |
1 LED (red) charge
1 LED (green) RUN
1 LED (red) error |
| Signalling function |
Servo status and fault codes five 7-segment display units |
| Marking |
CSA
CULus
CE |
| Type of cooling |
Integrated fan |
| Operating position |
Vertical |
| Product compatibility |
Servo motor BCH2 (130 mm, 1 motor stacks) at 500 W
Servo motor BCH2 (80 mm, 2 motor stacks) at 750 W
Servo motor BCH2 (130 mm, 1 motor stacks) at 600 W |
| Width |
55 mm |
| height |
150 mm |
| Depth |
146 mm |
| Net weight |
1 kg |
| Output current 3s peak 2 |
13.5 A at 220 V |
| Output current 3s peak 3 |
13.5 A at 220 V |
Schneider
